Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Torr JoJoshakar
Country: French Guiana
Language: English (Spanish)
Genre: Science
Published (Last): 17 February 2016
Pages: 142
PDF File Size: 8.88 Mb
ePub File Size: 9.26 Mb
ISBN: 408-1-51988-686-9
Downloads: 32667
Price: Free* [*Free Regsitration Required]
Uploader: Zulum

How often should I have my Hasselblad serviced? Camera body ELD Front bayonet plate Front plate reassembly Fit the four bayonet tongues and secure with eight screws They had seen so many bodies hasslsblad up from the two previous versions of the brake that, when working on a body, the first thing they would do would be to remove the new style brake. In this case, you will not see any number in the window. When I overhaul a lens, I usually replace the flash contact and the main spring.

This booklet makes the repairs so easy that a small child could do the repairs.

This manual contains 98 pages and is a photocopy of the original. Everything on it works well, except for the shutter release.

The upper flap, sooner or later, would start to crack at the axle. This is carried out as follows: This creates a lot of pressure on the two feet on the bottom of the body, and will eventually cause the feet to bend. Back to Top Is it better to store my camera bodies and lenses wound or in the fired position?

Page 15 and cable holder The shutter blades should close down, then open instantaneously, stay open for one second, and then close again. Take pictures and advance the film in the usual way until the camera and the release both lock up. Page 12 Camera body ELD Disassembly Rear plate Remove the screw from the centre of the large gear and lift the gear clear.

It is not uncommon for a crack to appear in a blade. The foam wears, and eventually will wear to the point that repalr will allow light to enter the magazine and fog the film when you remove the dark slide.


Hasselblad Historical – V-System manuals

Because the crack is very small and is hidden by the smaller piece that is hasslebkad to the blade, you cannot see this crack by looking into your lens. Make sure the camera is released. If the shutter is dragging at one second, it is an indication that the shutter needs to be cleaned and lubricated. The reason I wrote this manual is that I saw too many people being cheated by the so called good repair shops.


Camera body ELD Adjustment Check that the flat side of gear is parallel with the rear section. Page 14 Camera body ELD Disassembly Right and left hand wall Remove or cut the foam plastic pad rwpair get access to the screws Switching from O to T opens the shutter and curtains and exposure is go on and on till you return the lever from T to O. You’d be surprised how many cracked shutter blades I find. The nylon stop is replaced during an overhaul to prevent this from happening. This way, you won’t get caught with two dead batteries.

What is the proper procedure for attaching or removing extension tubes? Wind the body again, turn your strobe on, and attach the synch cord to the lens. If I install a brake assembly in wlm camera body, it is because someone had removed the brake.

Then, there are two smaller pieces that are riveted to one end of the blade; one on the top and one on the bottom. Charlie, Something made me write: There is a way, however, to “fingerprint” your magazines. Did you ever get your film back from the lab, only to discover there was a problem, such as a light leak or bad film spacing, and you didn’t know which magazine was the culprit?

500 EL/M won’t fire with pressing of release button

This is done by turning gear haasleblad Unit for infrared remote release of the Hasselblad ELD. Of course, it’s not good when these things happen, but at least you’ll notice it right away, and you can switch cameras and continue shooting. Should I operate it with one or two batteries? Remove the small nuteccentric and bearing pin The manual goes out of its way to be unhelpfull, with the bit about checking the battery miles from the other sections about the battery, and it does not say if a blown furse prevents you getting a “good battery reading” on the battery test LEDs, but I think there is only one fuse, and if it goes you cannot mwnual on or do very much at all with the camera.


Back to Top Why did you install or replace the brake assembly in my camera body? Page 38 Camera body ELD Adjustment Check the mirror 45 angle using the sighting tube which fits in the holder on the gauge. Tighten the locking screw. Can I use film in my older style Magazine 12? Insert the spool holder into the magazine housing and lock it. Doing majual can damage the ellm key on the body. Remove the screw Page 11 Camera body ELD Disassembly Remove the two long screws located towards the front of the camera shell.

Remove the dark slide and try to remove the magazine from the body. When I overhaul a film magazine, I usually replaced the light trap and nylon stop.

I’ve heard mnaual parts for the older C lenses are getting scarce. When the tripod foot and the rubber support have been removed, four holes are exposed allowing access to the four screws Page 10 Camera body ELD Manjal To remove the el, from the outer and inner mounting plates proceed as haswleblad see the exploded views 13 and This is due to the fact that the tooth on the body gear, which used to go into the opening in the magazine gear, is now hitting the first tooth.

This manual covers all the bodies except for the focal plane type, and the motorized bodies. If you are photographing a wedding, it is a good idea to perform this particular check each time you change film magazines.